Message 26921 in TECH.WW
From: G8MNY
Date: Thu, 30 Jul 26 08:40:00 Z
Newsgroups: TECH.WW
Subject: A Simple Telephone Tester
Message-ID: <643_GB7CIP>
Path: N2MH4|DK0WUE|VK5LEX|VE3KPG|GB7CIP
R:260730/0850Z 34628@N2MH4.#SENC.NC.USA.NOAM LinBPQ6.0.24
R:260730/0849Z 33008@DK0WUE.#BAY.DEU.EU LinBPQ6.0.25
R:260730/0849Z 31799@VK5LEX.#ADL.SA.AUS.AUNZ LinBPQ6.0.25
R:260730/0848Z 27573@VE3KPG.#ECON.ON.CAN.NOAM BPQ6.0.25
R:260730/0840Z @:GB7CIP.#32.GBR.EURO #:643 [Caterham Surrey GBR] $:643_GB7CIP
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Updated Sep 15)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
Ever needed to test the functions of a pair of Phones Answering machine, FAX,
Modem etc. without 2 telephone lines? This is a simple tester I knocked up in a
dual phone socket, plus a plug top PSU, to mimic most telephone line functions.
FEATURES
PHONE 1 "off hook" can listen to dial tone
Manual ringing of PHONE 2
PHONE 2 "off hook" removes dial tone from PHONE 1
PHONE 1 "on hook" causes line reversal to PHONE 2 (release the call test)
Variable line loss
Line status LED indicators
PLUG TOP PSU
u1
100V
The 50V 1W zener is actually series of zeners, T1 is any 200mA 100V 2W NPN.
The transformer's AC voltage is not high enough to ringing a phone directly, so
it is used to drive a line reversing relay to make the ringing.
A small u1 capacitor takes off some of higher harmonics of the AC to mimic dial
tone.
TEST CIRCUIT
Both relays are double changeover (only 1 needs to be) 28V 7mA DIL type, with
4k coil resistance, note some types may have internal diodes so polarity may
matter! During ringing RELAY 1 has to operate & release 50 time a seconds to
deliver +/- 50V to PHONE 2 to look similar to the 75V AC (17-25Hz) + 50V DC of
real telephone ringing.
The manual RING SWitch is a non locking double pole changeover.
Line loss & matching is all approximate, like the real world nothing is 600ohm!
But using 600 ohm test gear and blocking the DC etc. actual line losses could
be calibrated on the variable resistor scale (e.g. 10-30dB Max). A more
realistic dummy line and noise sources could be used as the middle section if it
was important (e.g. for a high speed modem evaluation).
REAR VIEW LAYOUT
In UK jack pins 2 & 5 are the 2 wire line, and a 3rd (pin 3) wire may be used
for the phones ringer path capacitor normally in the master socket. See your
local telecomms Co. (POTS) arrangements if different from UK.
PHONE CALL SIMULATION
1/ Connect 2 PHONE devices.
2/ Lift PHONE 1, LED 1 lights up, listen to buzzing dial tone & U have "Blow".
3/ Intermittently operate ringing switch (concadance ringing).
4/ Does PHONE 2 ring? (LED 2 lights dimly to ringing) Can it answer the call?
5/ On answer, LED 2 lights, PHONE 2 has "Blow", & PHONE 1 dial tone disappears
& a transmission path to PHONE 2 is made.
6/ Can you talk or send data both ways over transmission paths, is loss OK?
7/ Clear down PHONE 2, LED 2 goes out, & dial tone is returned to PHONE 1.
8/ If you cleared down PHONE 1 first instead, then PHONE 2 gets a line
polarity reversals, which should cause automatic kit to hang up & clear the
line for the next call. I found some kit just times out instead!
REAL PHONE TONES
DTMF-Telephone Standards Touch-Tone dialing
Touch-tone was a registered trademark of AT&T. It is also known as dual-tone
multiple frequency (DTMF) signaling!
The two tones in a 4 x 3 keypad matrix, a low-frequency tone and a high
frequency tone, to specify 1 of the 16 options. Pressing 2 keys in the same
row/column, normal results in a single tone. The 2 tones must not clip & mix
as the DTMF Rx IC uses the presence of more than 2 tones the identify the
signal non DTMF and ignores it.
TONE HIGH 1209Hz 1336Hz 1477Hz (1633Hz)
LOW
697 Hz 1 2 3 (A)
770 Hz 4 5 6 (B)
852 Hz 7 8 9 (C)
941 Hz * 0 # (D)
Level each tone: -6 to -4 dBm
Maximum difference in levels: 4 dB
Maximum level (pair): + 2 dBm
Pulse width: 50 msec
Time between digits: 45 msec minimum
DIAL TONE: 350-440 Hz
BUSY TONE: 480-620 Hz, with 60 interruptions per minute
EQUIPMENT ENGAGED TONE: sounds like busy tone, but slightly different!
RINGING TONE: 440-480 Hz, 2sec on, 4sec off
RINGING VOLTAGE: 17-22Hz 75V AC to earth & -50V DC. (155V peak!)
(cacadance) Load AC 1000ohms via a 1.8/0.9uF.
LINE CURRENT: Around 50mA, typically 10V across a phone in use.
Why Don't U send an Interesting Bul?
73 de John G8MNY @ GB7CIP
← Return to Bulletin List